Pipe Tools

Flat patterns for pipe insulation cladding and wraparound saddle templates. Calculate, print 1:1, cut. No account, nothing paywalled.

Cladding pattern

Diameters are measured over the insulation — pipe OD + 2 × insulation thickness.

Patterns are developed on the outside diameter over the insulation; strictly the mean diameter (outside diameter minus one sheet thickness) is correct — at 0.8 mm sheet the circumference is overstated by about 2.5 mm (0.3%), within normal cladding practice.

Long radius ≈ 1.5 × nominal bore
Incl. 2 end gores

One rectangle wraps the straight. The dashed line is where the lap starts — the extra strip overlaps and gets riveted or screwed.

Axial, large face to small face

Concentric reducer developed as a true cone frustum sector. Eccentric reducers need a different development — not covered here.

Flat end cap: cut the outer circle, fold or swage the skirt down at the dashed circle line.

Pattern

3D previewdrag to spin · auto-rotates
Ordinates — mark these on the sheet if you are laying out by hand

How the elbow gore works

  1. Cut 2 end gores and 3 middle gores for the piece count you set.
  2. The pattern is drawn with the outside of the bend (heel) at the centre of the sheet and the throat at both edges.
  3. Roll each gore to the cladding diameter, overlap the lap strip, and work from one tangent end toward the other, riveting as you go.

Saddle / wraparound template

The cut line for a branch pipe landing on a header pipe — tee or lateral. Wrap the printed template around the branch, mark, cut.

90 = tee · 45 = lateral
Straight strip above the cut line — wrap edge stays square

Use the outside diameters of the actual pipes here — for a saddle the branch is cut to the header's outside surface. The header hole below is drawn to the branch OD — see the warning under “Hole in the header” before cutting it, and do not add a fit-up gap to the hole (a gap makes the hole bigger, not smaller).

Branch wrap template

3D previewdrag to spin · auto-rotates
Ordinates — distance around branch vs. cut depth from the reference edge

Hole in the header

Where the branch lands — mark this outline on the header to cut the hole.

Warning — hole size: this outline is drawn to the branch outside diameter (OD). For a set-on branch, cut the bore instead — OD minus two wall thicknesses — cutting the outline exactly leaves the hole oversize by about one wall thickness all round. For a set-in / through branch, the OD hole shown is correct.

Using the template

  1. Print 1:1, tape the tiles together, and measure the 100 mm scale bar on a tile before trusting it.
  2. Wrap the template around the branch with the straight reference edge square to the pipe, seam the edges together, and mark the curve.
  3. The two low points of the curve sit on the header's centreline sides; the high points face along the header. Cut, then dress to fit.

Pipe offset calculator

Simple and rolling offsets with standard elbow angles. Travel is centre-to-centre of the two elbows.

Sideways shift between the two runs
Up/down shift — 0 for a flat offset

To get the cut length of the travel piece, subtract the two elbows' centre-to-end take-outs from the travel, and add your weld gaps.

Result

All lengths centre-to-centre unless noted.

3D previewdrag to spin · auto-rotates

Steel pipe sizes — ASME B36.10 (American)

Outside diameter is the same for every schedule at a given NPS. Wall and bore shown for Schedule 40 (STD weight up to 10″).

NPSOD (in)OD (mm)Sch 40 wall (mm)Bore / ID (mm)

Use loads that OD into the cladding tool's Pipe OD — or pick NPS / DN sizes directly from the preset lists in the cladding and saddle tools. For cladding, add 2 × insulation thickness to the OD. For saddles, use the OD of both pipes exactly as they are.

Patterns are developed from the exact cylinder / cone geometry — the same maths the paid apps use — and drawn at true size. Always run the scale check on the first printed tile: if the bar does not measure exactly 100 mm, reprint at “Actual size / 100%” with fit-to-page off. No printer? Use the On-screen 1:1 check — hold a ruler to the screen, slide the zoom until the bar measures exactly 100 mm, and the pattern on screen is true size. Check a first cut against the pipe before committing a full sheet.